House Rendering

Guide · Homeowners · 4 min read · Updated 17 November 2026

Silicone vs Monocouche vs Sand and Cement Render: Which to Choose

Short answer

Silicone render is a thin, through-coloured, water-repellent finish over a mesh-reinforced basecoat, costing about £60–£95 per m² and needing little upkeep. Monocouche is a thicker single-coat through-coloured render at £55–£85 per m², suited to consistent blockwork. Sand and cement is cheapest at £45–£70 but needs painting. Lime is the right choice for solid-walled period homes that need to breathe.

Silicone vs Monocouche vs Sand and Cement Render: Which to Choose

The four main systems compared

Render systems differ in thickness, flexibility, breathability and finish. Choosing the right one depends on the wall underneath as much as the look you want. A system that suits modern blockwork can damage an old solid brick wall, and a thin coat that works beautifully on a flat, even surface may highlight every bump on an uneven one.

The table summarises the main differences. Prices are typical supplied-and-applied rates per square metre for 2026, before scaffolding.

SystemPrice per m²FinishBest for
Silicone£60–£95Fine texture, through-colouredMost modern walls, low upkeep
Monocouche£55–£85Scraped texture, through-colouredConsistent blockwork, new builds
Sand and cement£45–£70Smooth or textured, paintedBudget projects, traditional look
Lime£70–£120Soft, natural, limewashedSolid-walled and listed buildings

Silicone render

Silicone render is a thin-coat system. The wall is prepared and fitted with beads, then a cement-based or polymer basecoat is applied with alkali-resistant glass fibre mesh embedded in it to resist cracking. After curing, a primer goes on, followed by a coloured silicone topcoat usually around 1.5mm to 2mm thick, floated to a fine, even texture.

Silicone resins make the finish water-repellent while still allowing water vapour to escape, so rain tends to bead and run off, taking dirt with it. That is why silicone often stays cleaner than other renders. It comes in a wide range of colours and does not need painting. It is slightly more flexible than cement-based finishes, which helps with minor movement. Shaded walls can still grow algae over time and may need an occasional clean.

Monocouche render

Monocouche, French for single layer, is a through-coloured cement-based render applied in one thick pass, often 15mm to 20mm, by spray machine or trowel. Once partly set, the surface is scraped with a toothed tool to remove the outer skin and leave a consistent, slightly textured finish.

It is quicker to apply than traditional two-coat render and does not need painting. It works best on even, consistent backgrounds such as modern blockwork, where suction is uniform. On mixed or uneven backgrounds it can show patchy colour, known as shading, and it is less forgiving of movement than thin-coat systems. Because it is cement-based and fairly rigid, it is not suitable for old solid walls that need to breathe.

Sand and cement render

Traditional sand and cement render is applied in two coats: a scratch coat keyed with a comb to give grip, then a float coat finished smooth or textured. It can also be finished with a roughcast or dry dash of pebbles. It is the cheapest system to apply and many plasterers can do it well.

The downside is maintenance. Sand and cement is grey, so it is usually painted with masonry paint, and that paint needs renewing roughly every eight to ten years. It is relatively rigid, so hairline cracking is common, especially if the mix is too strong or curing is rushed. Like monocouche, it should not be used on solid-walled older properties that rely on breathable finishes.

Lime render for older homes

Lime render uses natural hydraulic lime or lime putty with sand, applied in several coats and allowed to cure slowly. It is softer and more vapour-permeable than cement, so moisture in solid walls can evaporate rather than becoming trapped. That is essential on pre-1919 homes built without cavities or damp-proof membranes.

Lime is slower and more weather-sensitive to apply, which is why it costs more. It is usually finished with limewash, which needs renewing every few years. Replacing lime with cement-based render on historic fabric is generally not acceptable on listed buildings, and listed building consent is needed for changes to the external finish.

  • Modern cavity walls: silicone or monocouche
  • Uneven or mixed backgrounds: silicone over a mesh basecoat
  • Tight budget and happy to repaint: sand and cement
  • Solid walls, pre-1919 homes and listed buildings: lime

Textures, colours and decorative finishes

Each system offers a different range of looks. Silicone is usually supplied in grain sizes from about 1mm to 2mm, with the larger grain giving a slightly coarser texture that hides minor imperfections better. Monocouche gives a scraped, open texture that varies a little with the applicator's technique. Sand and cement can be finished smooth, with a sponge float texture, or with a roughcast or dry dash of stones for a hard-wearing, traditional finish.

Colour choice is wider than many people expect. Most silicone and monocouche manufacturers offer dozens of standard shades plus custom tinting, though very dark colours absorb more heat and can be more prone to stress cracking and fading on sunny elevations. Whites and off-whites are the most popular, but soft greys and warm stone tones hide dirt better. Decorative quoins, window surrounds and banding can be formed in contrasting colours or with render bands for added character.

Making the decision

Start with the wall. If it is solid masonry from before the First World War, lime is usually the right answer. If it is a modern cavity wall, any of the cement or silicone systems can work. Then weigh upfront cost against upkeep, and decide whether a through-coloured finish or a painted one suits your taste.

We arrange vetted, insured local rendering specialists who survey the wall first and recommend a system based on its construction and condition, rather than defaulting to whatever they always use.

Questions people also ask

Is silicone render better than monocouche?

For most homes silicone is the more forgiving choice. It is applied over a mesh-reinforced basecoat, resists cracking better, stays cleaner and works on a wider range of backgrounds. Monocouche is slightly cheaper and quick to apply, but it suits consistent blockwork best and can show patchy colour on mixed backgrounds.

Does silicone render need painting?

No. Silicone render is through-coloured, so the colour runs through the finish and it does not need painting to look good. Over time, shaded or north-facing walls may grow algae and benefit from a gentle biocide clean. Painting silicone render is possible with compatible products but rarely necessary.

Can you put silicone render on an old house?

On modern cavity-walled homes, yes. On older solid-walled houses built before about 1919, a breathable lime render is usually more appropriate because cement-based systems can trap moisture in the masonry. Some breathable thin-coat systems exist, but a survey of the wall should come first.

Written and checked by the House Rendering team. Read our editorial policy.

Get a free house rendering quote

Tell us what you need and we'll come back with a clear price.

Request a quote