Guide · Homeowners · 4 min read · Updated 17 November 2026
The House Rendering Process: What Happens and How Long It Takes
Short answer
Rendering a house involves a survey, scaffolding, preparing and priming the walls, fitting beads at corners, edges and above the damp-proof course, applying a mesh-reinforced basecoat, then the finish coat. A typical semi takes around one to three weeks on site depending on the system, preparation and weather. Render should not be applied in frost, heavy rain or very hot sun.
Survey and preparation planning
A good rendering job starts with a survey. The specialist checks what the walls are built from, whether existing render or paint is sound, where the damp-proof course sits, and how windows, sills, pipes and features will be detailed. Tapping the wall reveals hollow areas of old render that must come off. Any damp, cracking or movement needs explaining before new render hides it.
From the survey comes a written specification listing the system, preparation, beads, mesh, colour and texture. That document is what you compare between quotes and what you check against on site.
Stage by stage on site
Scaffolding goes up first, with sheeting if the weather is changeable. Downpipes, lights, satellite dishes and cables are removed or loosened. Windows, doors and paving are masked. Old render or pebbledash is hacked off where needed, and loose mortar is raked out. Sound surfaces are cleaned and treated with a primer or bonding agent to control suction.
Beads are then fixed: angle beads on external corners, stop beads at edges and around openings, and a bellcast bead above the damp-proof course so the render does not bridge it and water drips clear. The basecoat is applied with alkali-resistant mesh embedded across the whole wall. Once cured, the finish coat goes on and is textured, scraped or floated to suit the system.
| Stage | Typical time on a semi |
|---|---|
| Scaffolding erected | 1 day |
| Preparation and hacking off | 1–4 days |
| Beads and primer | 1–2 days |
| Basecoat with mesh | 2–3 days plus curing |
| Finish coat | 2–3 days |
| Refitting, clean-up and scaffold down | 1–2 days |
Weather and curing
Render is weather-sensitive. Most manufacturers advise against applying cement-based or silicone render when temperatures are below about 5°C or likely to fall below it before the render has set, in rain, or in strong direct sun and drying winds. Frost can destroy a fresh coat, and rain can wash out the surface or cause streaking.
Each coat needs time to cure before the next goes on. Thin-coat basecoats usually need at least a day or two, while lime renders need far longer between coats and must be protected from drying out too fast. This is why rendering programmes slip in poor weather, and why spring to early autumn is the busiest season.
- Avoid frost and temperatures below about 5°C
- Do not render in rain or when rain is imminent
- Shade fresh render from strong sun and wind
- Allow each coat its full curing time
What you need to do as the homeowner
Clear the base of the walls of plants, pots, bins and garden furniture. Move cars off the drive if the scaffold needs the space. Let neighbours know when scaffolding will go up, especially on shared paths. Keep windows closed on the elevation being worked on, as render dust and splashes travel.
Decide on colour and texture early. Ask to see a sample panel on your wall before the whole house is done, because colours look different in daylight and on a large area. Agree what happens to existing fittings such as hanging baskets, alarm boxes and outside taps.
Common problems and how to avoid them
Cracking is the most common complaint. It usually comes from missing mesh, a basecoat that was too thin, rushing between coats, or movement in the wall that was not addressed. Patchy colour on monocouche often comes from uneven suction or applying in changing weather. Staining below sills happens when sills do not project far enough past the new render.
Bridging the damp-proof course is a serious mistake. If render runs down to the ground, it can draw moisture up past the damp-proof course and into the wall. A bellcast bead above the damp-proof course prevents this. Ask your installer to confirm these details in the specification.
Rendering with external wall insulation
If you are adding external wall insulation, the process has extra stages. After preparation, insulation boards such as expanded polystyrene, mineral wool or wood fibre are fixed to the wall with adhesive and mechanical fixings, staggered like brickwork so joints do not line up. Corners, window reveals and the base of the wall get special detailing, including a starter track and often a different, more water-resistant board below the damp-proof course level.
The boards add depth to the wall, so window sills usually need extending, downpipes need longer brackets, gas and electricity meter boxes may need moving and the roof eaves may need extending to keep the top of the insulation protected. Once the boards are fixed and rasped flat, the mesh-reinforced basecoat and finish coat go on as normal. Allow extra time in the programme for these stages, often an additional week or more on a typical house.
Aftercare and handover
When the scaffold comes down, walk around the house with the contractor and check the finish, the beads and the edges around windows and doors. Make sure fittings are refitted securely and penetrations are sealed. Keep the product details and colour reference so future repairs can be matched.
We arrange vetted, insured local rendering specialists who provide a written specification before work starts and walk the finished job with you at handover.
Questions people also ask
How long does it take to render a house?
A typical semi-detached house takes around one to three weeks on site, depending on the system, how much preparation is needed and the weather. Hacking off old render adds days, while poor weather can pause work. External wall insulation adds time for fixing boards before the render coats.
Can you render in winter?
It is possible on mild, dry days, but risky. Most manufacturers advise against applying render below about 5°C or when frost is forecast before it sets. Winter work often needs scaffold sheeting and careful scheduling. Spring to early autumn gives the most reliable results.
Why does new render crack?
Common causes include missing or poorly embedded mesh, a basecoat that is too thin, coats applied before the previous one cured, overly strong cement mixes, and unaddressed movement in the wall. Fine shrinkage cracks can also appear in traditional sand and cement. Good preparation and a mesh-reinforced system reduce the risk.
Written and checked by the House Rendering team. Read our editorial policy.
More guides
How Much Does It Cost to Render a House in the UK? 2026 Prices
Rendering a house in the UK typically costs £45–£70 per m² for painted sand and cement, £55–£85 for monocouche, £60–£95 for a silicone render system…
Silicone vs Monocouche vs Sand and Cement Render: Which to Choose
Silicone render is a thin, through-coloured, water-repellent finish over a mesh-reinforced basecoat, costing about £60–£95 per m² and needing little…
Does Rendering a House Need Planning Permission? UK Rules
In England, rendering a house can be permitted development if the materials are similar in appearance to the existing house. In conservation areas,…
Lime Render for Period Homes: Why Cement Render Causes Damp
Period homes with solid walls, usually built before about 1919, rely on moisture evaporating out through the wall surface. Cement render is dense and…
Get a free house rendering quote
Tell us what you need and we'll come back with a clear price.
Request a quote